Fiber Optic Cable Shop
ABOUT US • CUSTOMER SERVICE • CONTACT US
toll free: 800-777-6269
Search


Technical Information Center



[ Home > Media Converters > Multimode Media Converters > Multimode 10/100/1000 (Gigabit) Media Converters > Media Converter, Multimode Gigabit, 10/100/1000BaseTX to 1000BaseSX (SFP with LC), 220/550m ]



Media Converter, Multimode Gigabit, 10/100/1000BaseTX to 1000BaseSX (SFP with LC), 220/550m

This is a very flexible media converter which allows the use of one or two SFP slots for mini-GBICs. It transfers data over fiber at 1000Mbps and connects to copper Ethernet at 10, 100 or 1000Mbps, while auto-sensing the correct speed. It has ample LEDs to monitor and diagnose its operation. Dip switches allow activation of LFP (Link Fault Passthru) to relay connection problems to other devices on the network. This version includes a module for multimode operation at 1000Mbps (850nm). The copper connector is a RJ-45, the fiber connectors are LC.

TECHNICAL SPECIFICATIONS, Model: ME-3800-MM3-LC:

CONNECTORS/SLOTS:
P1 — RJ-45 & SFP Slot #1 (both not available at the same time)
P2 — SFP Slot #2 comes with 1000BaseSX (850nm) Multimode(LC connectors)

DATA TRANSFER RATE:
10/100/1000Mbps (auto-negotiation or forced mode) for Ethernet
1000Mbps for fiber

MAX CABLE DISTANCES:
50/125µm Multimode fiber, 500/550m
62.5/125µm Multimode fiber, 220/275m

DUPLEX MODE:
Full-Duplex for 1000Base-SX
Full-/Half-Duplex (auto-sense) for 10/100Base-TX

LEDs:
Unit — PWR (Power)
P1 — SFP LNK/ACT (Link/Activity)
P1 — TP LNK/ACT (Link/Activity)
P1 — TP SPD (Speed for 10/100/1000Mbps)
[ Green for 1000Mbps, Amber for 100Mbps, OFF for 10Mbps ]
P2 — SFP LNK/ACT (Link/Activity)

ENVIRONMENTAL REQUIREMENTS:
Power Requirement: 0.9A up @ +5VDC
Power Consumption: 3.6W
Ambient Temperature: 0° to 40° C
Humidity: 5% to 90%
Dimensions: 140.7(5.5) x 87.7(3.5) x 29.4mm(1.2in.)(HxWxD)

STANDARDS:
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3z/ab 1000Base-T
IEEE 802.3x full-duplex flow control,
1000Base-SX/LX

EMISSION & SAFETY REGULATIONS:
FCC Part 15 Class A & CE Mark Approval

ADDITIONAL FEATURES
Link Fault Pass-Through (LFP) With LFP enabled (selectable by DIP-Switch at rear panel), if any segment cable is broken, both ports in each converter will be turned OFF, i.e. no Link LED. If all segment cables are well connected, both ports in each converter will be turned ON, i.e. Link LED.


Please Note-- Price is for each unit. Normally two are required. If you are ordering only one unit, please indicate in our comments section (upon checkout) the make and model of the switch or media converter at the other end of the fiber so we may include the appropriate compatible SFP module.


Item #: ME-3800-MM3-LC
$425.00
Quantity:




PLEASE CALL FOR LENGTHS AND CONFIGURATIONS NOT SHOWN



Copyright © Fiber Optic Cable Shop. All World Rights Reserved.